Bookmarks

Yahoo Gmail Google Facebook Delicious Twitter Reddit Stumpleupon Myspace Digg

Search queries

sprocket xt 600, starter for 1984 honda 650 nighthawk, how to bypass crank position sensor honda, jensen interceptor ignition timing, rfactor f3 mod, temporary fix for crankshaft position sensor, rear brakes at 4mm, dr 350 cdi, 1992 dodge spirit fuel system, how long will 4mm brake pads last

Links

XODOX
Impressum

#1: Key Alarm Program 95 Integra

Posted on 2006-07-21 22:39:18 by unknown

Hello everyone,

I'm trying to install a set of keyless alarms on my 95 Integra
since the old ones are not working. In the directions that I got it
said to turn the key to II and then press and hold the valet override
switch and keep holding it until the LED on the steering wheel start
to blink. The problem is when I got the car, the switch was broken (at
least I think it was this switch). If I'm right it looks like it runs
to another connection underneath the drivers dash which I'm trying to
short out with a paper clip but doesn't seem to be working. The wires
appear blue and black until the connection and then change to black
orange and blue. Is this the correct procedure; and am I shorting the
correct wires? I'll try to post a picture later tonight if it'll help.

Thanks in advance,

Nick

Report this message

#2: Re: Key Alarm Program 95 Integra

Posted on 2006-07-21 23:07:33 by Seth

&lt;Nick&gt; wrote in message news:<a href="mailto:vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com..." target="_blank">vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com...</a>
&gt; I'm trying to install a set of keyless alarms on my 95 Integra
&gt; since the old ones are not working. In the directions that I got it
&gt; said to turn the key to II and then press and hold the valet override
&gt; switch and keep holding it until the LED on the steering wheel start
&gt; to blink. The problem is when I got the car, the switch was broken (at
&gt; least I think it was this switch). If I'm right it looks like it runs
&gt; to another connection underneath the drivers dash which I'm trying to
&gt; short out with a paper clip but doesn't seem to be working. The wires
&gt; appear blue and black until the connection and then change to black
&gt; orange and blue. Is this the correct procedure; and am I shorting the
&gt; correct wires? I'll try to post a picture later tonight if it'll help.

I don't think anybody can help you since you don't state the make and model
of the alarm in question. It sure doesn't sound like a Honda alarm.

Report this message

#3: Re: Key Alarm Program 95 Integra

Posted on 2006-07-21 23:30:16 by unknown

It's the factory Alarm.

Thanks,
Nick

On Fri, 21 Jul 2006 17:07:33 -0400, &quot;Seth&quot;
&lt;<a href="mailto:seth_lermanNOSPAM&#64;hotmail.com" target="_blank">seth_lermanNOSPAM&#64;hotmail.com</a>&gt; wrote:

&gt;&lt;Nick&gt; wrote in message news:<a href="mailto:vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com..." target="_blank">vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com...</a>
&gt;&gt; I'm trying to install a set of keyless alarms on my 95 Integra
&gt;&gt; since the old ones are not working. In the directions that I got it
&gt;&gt; said to turn the key to II and then press and hold the valet override
&gt;&gt; switch and keep holding it until the LED on the steering wheel start
&gt;&gt; to blink. The problem is when I got the car, the switch was broken (at
&gt;&gt; least I think it was this switch). If I'm right it looks like it runs
&gt;&gt; to another connection underneath the drivers dash which I'm trying to
&gt;&gt; short out with a paper clip but doesn't seem to be working. The wires
&gt;&gt; appear blue and black until the connection and then change to black
&gt;&gt; orange and blue. Is this the correct procedure; and am I shorting the
&gt;&gt; correct wires? I'll try to post a picture later tonight if it'll help.
&gt;
&gt;I don't think anybody can help you since you don't state the make and model
&gt;of the alarm in question. It sure doesn't sound like a Honda alarm.
&gt;

Report this message

#4: Re: Key Alarm Program 95 Integra

Posted on 2006-07-21 23:47:12 by unknown

One additional note....I don't have any remotes that are working.

On Fri, 21 Jul 2006 17:30:16 -0400, Nick &lt;&gt; wrote:

&gt;It's the factory Alarm.
&gt;
&gt;Thanks,
&gt;Nick
&gt;
&gt;On Fri, 21 Jul 2006 17:07:33 -0400, &quot;Seth&quot;
&gt;&lt;<a href="mailto:seth_lermanNOSPAM&#64;hotmail.com" target="_blank">seth_lermanNOSPAM&#64;hotmail.com</a>&gt; wrote:
&gt;
&gt;&gt;&lt;Nick&gt; wrote in message news:<a href="mailto:vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com..." target="_blank">vfe2c2pqoka8tivfquc9386sh043pgjmmb&#64;4ax.com...</a>
&gt;&gt;&gt; I'm trying to install a set of keyless alarms on my 95 Integra
&gt;&gt;&gt; since the old ones are not working. In the directions that I got it
&gt;&gt;&gt; said to turn the key to II and then press and hold the valet override
&gt;&gt;&gt; switch and keep holding it until the LED on the steering wheel start
&gt;&gt;&gt; to blink. The problem is when I got the car, the switch was broken (at
&gt;&gt;&gt; least I think it was this switch). If I'm right it looks like it runs
&gt;&gt;&gt; to another connection underneath the drivers dash which I'm trying to
&gt;&gt;&gt; short out with a paper clip but doesn't seem to be working. The wires
&gt;&gt;&gt; appear blue and black until the connection and then change to black
&gt;&gt;&gt; orange and blue. Is this the correct procedure; and am I shorting the
&gt;&gt;&gt; correct wires? I'll try to post a picture later tonight if it'll help.
&gt;&gt;
&gt;&gt;I don't think anybody can help you since you don't state the make and model
&gt;&gt;of the alarm in question. It sure doesn't sound like a Honda alarm.
&gt;&gt;

Report this message

#5: Re: Key Alarm Program 95 Integra

Posted on 2006-07-22 00:05:29 by Seth

&lt;Nick&gt; wrote in message news:<a href="mailto:pqh2c2lad66dkg6mvc1plvg58gbngbvoil&#64;4ax.com..." target="_blank">pqh2c2lad66dkg6mvc1plvg58gbngbvoil&#64;4ax.com...</a>
&gt; It's the factory Alarm.

Probably really an Alpine. In the early 90's, all of the Honda alarms were
Alpine.

Do you see your remotes here? <a href="http://www.autotechs.com/subcat65.htm" target="_blank">http://www.autotechs.com/subcat65.htm</a>

Report this message

#6: Re: Key Alarm Program 95 Integra

Posted on 2006-07-22 00:40:46 by unknown

Yes is HO-3BB. I checked a few older postings on Google News and found
that the instructions are correct. I just can't seem to get the
blinking LED after I link the wires together.



On Fri, 21 Jul 2006 22:05:29 GMT, &quot;Seth&quot;
&lt;<a href="mailto:seth_lermanNOSPAM&#64;hotmail.com" target="_blank">seth_lermanNOSPAM&#64;hotmail.com</a>&gt; wrote:

&gt;&lt;Nick&gt; wrote in message news:<a href="mailto:pqh2c2lad66dkg6mvc1plvg58gbngbvoil&#64;4ax.com..." target="_blank">pqh2c2lad66dkg6mvc1plvg58gbngbvoil&#64;4ax.com...</a>
&gt;&gt; It's the factory Alarm.
&gt;
&gt;Probably really an Alpine. In the early 90's, all of the Honda alarms were
&gt;Alpine.
&gt;
&gt;Do you see your remotes here? <a href="http://www.autotechs.com/subcat65.htm" target="_blank">http://www.autotechs.com/subcat65.htm</a>
&gt;

Report this message