| Engine swap From 4.0L YJ to 4.0L Cherokee [message #784197] |
Tue, 18 July 2006 00:44 |
|
I have a 1991 Jeep Wrangler. I am in process of swapping out the
engine. I was told that the engine I purchased was a 91 4.0L from a
Cherokee. It is 4.0L and everything looked great, until the sleeve for
my pilot bearing would not fit the new cherokee pilot bearing hole.
Mine is 1.05inches and it seams the cherokee pilot hole is roughly
..99inch. So I started looking closer at this engine. It apears from the
stamp on the block that it was manufactured in 94. Is this year engine
compatible with the 91 ? The tranny is ax15, and the mounts look right,
but before I go further (and purchase the new sleeve and pilot bearing)
I want to be certain this will work.
Thanks!
|
|
|
| Re: Engine swap From 4.0L YJ to 4.0L Cherokee [message #784200 ] |
Tue, 18 July 2006 01:37 |
|
They show two pilot bearings for the '94 six, a one inch like you
have and probably the 1.84" like your old engine's crank used,
fortunately both have the 3/4" input:
http://www.billhughes.com/temp/94pilot.jpg
God Bless America, Bill O|||||||O
mailto:LWHughes3rd [at] aol.com
jcarrington [at] gmail.com wrote:
>
> I have a 1991 Jeep Wrangler. I am in process of swapping out the
> engine. I was told that the engine I purchased was a 91 4.0L from a
> Cherokee. It is 4.0L and everything looked great, until the sleeve for
> my pilot bearing would not fit the new cherokee pilot bearing hole.
> Mine is 1.05inches and it seams the cherokee pilot hole is roughly
> .99inch. So I started looking closer at this engine. It apears from the
> stamp on the block that it was manufactured in 94. Is this year engine
> compatible with the 91 ? The tranny is ax15, and the mounts look right,
> but before I go further (and purchase the new sleeve and pilot bearing)
> I want to be certain this will work.
> Thanks!
|
|
|
| Re: Engine swap From 4.0L YJ to 4.0L Cherokee [message #784223 ] |
Tue, 18 July 2006 09:49 |
|
On Mon, 17 Jul 2006 22:44:35 UTC jcarrington [at] gmail.com wrote:
> I have a 1991 Jeep Wrangler. I am in process of swapping out the
> engine. I was told that the engine I purchased was a 91 4.0L from a
> Cherokee. It is 4.0L and everything looked great, until the sleeve for
> my pilot bearing would not fit the new cherokee pilot bearing hole.
> Mine is 1.05inches and it seams the cherokee pilot hole is roughly
> .99inch. So I started looking closer at this engine. It apears from the
> stamp on the block that it was manufactured in 94. Is this year engine
> compatible with the 91 ? The tranny is ax15, and the mounts look right,
> but before I go further (and purchase the new sleeve and pilot bearing)
> I want to be certain this will work.
> Thanks!
Those sound like the numbers I ran into when swapping out an BA 10/5
for an AX15 - the AX15 pilot shaft was several thou larger than the
old POS. I wound up going to one of the local parts stores and
getting a GM bushing that had the right inside hole and was as close
as possible on the outside. Wound up chucking the bushing on an arbor
in the drill press and using emory cloth to "polish" off about .010
<g>.
--
Will Honea
|
|
|
