| 96 intrepid rear drum brakes [message #767232] |
Tue, 06 June 2006 04:37 |
|
What size nut holds on the back brake hub on a
1996 Intrepid? I thought it was a 34mm deep socket
but it seems bigger than that. Thanks for any help.
|
|
|
| Re: 96 intrepid rear drum brakes [message #767235 ] |
Tue, 06 June 2006 12:26 |
|
den630 wrote:
> What size nut holds on the back brake hub on a
> 1996 Intrepid? I thought it was a 34mm deep socket
> but it seems bigger than that. Thanks for any help.
>
>
According to this thread (has what appears to be the procedure out of
the FSM) on DI.net:
http://www.dodgeintrepid.net/forums/showthread.php?t=70182&a mp;highlight=rear+drum+nut+size
some guy used a 1-7/8" socket, which, if correct, would translate into
either a 47 or 48mm. Torque would be 124 ft-lbs.
Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
|
|
|
| Re: 96 intrepid rear drum brakes [message #767254 ] |
Wed, 07 June 2006 04:05 |
|
"Bill Putney" <bptn [at] kinez.net> wrote in message
news:4el3miF1euv7lU1 [at] individual.net...
> den630 wrote:
> > What size nut holds on the back brake hub on a
> > 1996 Intrepid? I thought it was a 34mm deep socket
> > but it seems bigger than that. Thanks for any help.
> >
> >
> According to this thread (has what appears to be the procedure out of
> the FSM) on DI.net:
>
http://www.dodgeintrepid.net/forums/showthread.php?t=70182&a mp;highlight=rear+drum+nut+size
> some guy used a 1-7/8" socket, which, if correct, would translate into
> either a 47 or 48mm. Torque would be 124 ft-lbs.
>
> Bill Putney
> (To reply by e-mail, replace the last letter of the alphabet in my
> address with the letter 'x')
Thanks Bill I didn't even know that there was a www.dodgeintrepid.net web
site. There is allot of
good information on the site.
Thanks again
Den
|
|
|
| Re: 96 intrepid rear drum brakes [message #767257 ] |
Wed, 07 June 2006 04:39 |
|
den630 wrote:
> "Bill Putney" <bptn [at] kinez.net> wrote in message
> news:4el3miF1euv7lU1 [at] individual.net...
>
>>den630 wrote:
>>
>>>What size nut holds on the back brake hub on a
>>>1996 Intrepid? I thought it was a 34mm deep socket
>>>but it seems bigger than that. Thanks for any help.
>>>
>>>
>>
>>According to this thread (has what appears to be the procedure out of
>>the FSM) on DI.net:
>>
>
> http://www.dodgeintrepid.net/forums/showthread.php?t=70182&a mp;highlight=rear+drum+nut+size
>
>>some guy used a 1-7/8" socket, which, if correct, would translate into
>>either a 47 or 48mm. Torque would be 124 ft-lbs.
>>
>>Bill Putney
>>(To reply by e-mail, replace the last letter of the alphabet in my
>> address with the letter 'x')
>
>
> Thanks Bill I didn't even know that there was a www.dodgeintrepid.net web
> site. There is allot of
> good information on the site.
> Thanks again
> Den
You're welcome!
Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
|
|
|
